CJ70 Electronic Gong
The Dewhurst CJ70 Serial Electronic Gong is an audible indication for lift arrival at a floor, which also has output to control lantern arrows. This low profile serial unit offers the choice of a single or double tone and is designed to be connected to the Dewhurst 4 wire serial encoders (CH024/034 or CX-Basic). The CJ70 is suitable for use with the Dewhurst Profile station, which could also include the 30mm and 50mm ULSP digital display unit.
- Serial gong (used without displays)
- Outputs to control lantern arrows
- Single or double tone
- Low profile
- Can be used to meet M2/S2 Building Regulations
- Adjustable volume
- Works with CH024/CH034 Serial Encoder or CX-Basic Encoder Board
Visit Website: Dewhurst
Related products
Oil Collecting Pots
The round ETN®-oil collecting pot is designed for universal application on guide rail widths 5 - 16 mm. The square pot was developed for guide rail widths 5 - 28,6 mm. Visit Website: ETN
Guide Rail Clips
Attachment clamps for fastening guide rails.
GM Series
Giovenzana International B.V., widely recognized as a leader in elevator technology and the name that operators associate with security and quality, has created the new GM series of inspection boxes (complies with International Standard EN 81.20 and EN 81.50). The ergonomic design ensures maximum operator safety. Giovenzana designs and implements safety components for the world’s major chain lift manufacturers.
- Mushroom stopping device in accordance with IEC / EN 60947-5-5
- Mandatory Run button
- Operators are protected against accidental impacts at all times
- Cam switch (not selector) binding to the norm for inspection operation with solid drive and without margin of error in the switching
- Contact blocks with spring clamp conform to EN 60068-2-6 and EN 60068-2-27 and vibration
- resistant with IP20 degree of protection
- AC-15 and DC-13 contact blocks in accordance with EN 60947-5-1:2005 (1M cycles)
CJ50 & CJ60 Electronic Gongs
To complement our wide variety of Hall Lanterns, we have a range of electronic gongs. Audible notification of lift arrival at the floor is a code requirement.
- Single or double tone
- CJ50 & CJ60 stand-alone boxed version
- Can be used to meet M2/S2 Building Regulations
- Adjustable volume
Safe Space Mats
Light and heavy duty slip resistant safe space rigid mats.
- Suitable for pit floor and top of car.
- Slip resistant
- Compliant with the requirements of EN81-20
- 3 sizes to suit various areas
LED Shaft Lighting
Simple modular System - only 2 lengths of LED strip, 3m & 10m - enable any project to be built using the minimum of components - another benefit is that only a small section of the LED strip needs to be replaced if damaged, not the whole shaft length. LED strips are powered directly by 240V, no driver needed. The LED strips connect together to create shaft lighting systems suitable for any length of shaft up to 50 metres.
- Quick to install
- Emergency backup available
- Compliant with the requirements of EN81-20 and EN81-50
- Simple modular System
Plug an Play Emergency Car Lighting
Inples lighting production consists of small ceiling LED lights (lediera) that use power LED’s and a special power supply (driver) that switches them on. The Inples system is pre-wired and does not require additional external components and only takes a few minutes to install. The replacement of the ledieras and battery approximately every 5 years with the complete system every 10 years. Optional vandal resistant surround available. Visit Website: InPles
Pit Ladders
Static stepladder with spacers for vertical attachment to wall. This design is intended to be used in elevator shafts with a reasonable amount of space.
- quick and cost-efficient solution
- the spacers can be positioned on the shaft wall in pairs relatively freely
- short installation time
Emergency 12v Power Supply
This special power supply is the most powerful in its class, the result of 2 years of research and development combines the switching technology to our exclusive Aral, thus ensuring the required functionality at a very high quality and reliability of the finished product.
- most powerful in its class
- of very high quality and reliability
Lift HAWK Sensor
The Lift HAWK is a sensor fitted on the top of the lift car (TOC) which can remotely check the lift status through connection with a Digital Communication Platform (DCP) or Memcom+. Information such as the time of the last lift movement, current door status and time of the last door move can all be remotely tested using this device. The HAWK also self-learns the typical activity of a lift and can autonomously perform lift tests in periods of prolonged inactivity.
- Remotely test the lift status without having to connect to the lift controller
- Self-learning sensor performs autonomous tests when usage patterns are not typical
- Real-time monitoring through the Avire Hub
- Saves time and cost of visiting site for false call outs
- CAN or serial connections
- Compact mechanical footprint
- Quick and easy to install
Guide Rail Lubricators
We offer a range of guide rail lubricators.
- ETN 120
- ETN 170
- ETN 110
- ETN 100
- ETN-S
Spirators (Door closer)
Required by code, hoistway door closers or spirators are an important component that assures passenger safety by automatically shutting elevator doors whenever the car leaves a landing.
