LED Shaft Lighting
Simple modular System – only 2 lengths of LED strip, 3m & 10m – enable any project to be built using the minimum of components – another benefit is that only a small section of the LED strip needs to be replaced if damaged, not the whole shaft length. LED strips are powered directly by 240V, no driver needed. The LED strips connect together to create shaft lighting systems suitable for any length of shaft up to 50 metres.
- Quick to install
- Emergency backup available
- Compliant with the requirements of EN81-20 and EN81-50
- Simple modular System
Visit Website: A&A Electrical Distributors
Additional information
| Brand | A&A Electrical Distributors |
|---|
Related products
Guide Rail Clips
Attachment clamps for fastening guide rails.
Spirators (Door closer)
Required by code, hoistway door closers or spirators are an important component that assures passenger safety by automatically shutting elevator doors whenever the car leaves a landing.
Buzzer (EN-Buzz)
The EN-BUZZ has been designed to work with any button and controller where the button and illumination is wired using a 3 wire method. The common supply (24V d.c. ± 20%) to the button and illumination can be either polarity. One EN-BUZZ will be required for each set of car buttons and each landing station. There are two types of EN-BUZZ available, Standard (used with grille) and loud (used without grille). A 110V d.c. Standard version is also available, please refer to publication number PB169.
- Creates a bleep tone each time a call button is pressed and acknowledged
- Adjustable volume
- 12 – 24Vdc & 110Vdc options available
- Conforms to EN81-70
- Standard and loud versions available
Safe Space Mats
Light and heavy duty slip resistant safe space rigid mats.
- Suitable for pit floor and top of car.
- Slip resistant
- Compliant with the requirements of EN81-20
- 3 sizes to suit various areas
CJ50 & CJ60 Electronic Gongs
To complement our wide variety of Hall Lanterns, we have a range of electronic gongs. Audible notification of lift arrival at the floor is a code requirement.
- Single or double tone
- CJ50 & CJ60 stand-alone boxed version
- Can be used to meet M2/S2 Building Regulations
- Adjustable volume
Plug an Play Emergency Car Lighting
Inples lighting production consists of small ceiling LED lights (lediera) that use power LED’s and a special power supply (driver) that switches them on. The Inples system is pre-wired and does not require additional external components and only takes a few minutes to install. The replacement of the ledieras and battery approximately every 5 years with the complete system every 10 years. Optional vandal resistant surround available. Visit Website: InPles
Emergency 12v Power Supply
This special power supply is the most powerful in its class, the result of 2 years of research and development combines the switching technology to our exclusive Aral, thus ensuring the required functionality at a very high quality and reliability of the finished product.
- most powerful in its class
- of very high quality and reliability
CJ70 Electronic Gong
The Dewhurst CJ70 Serial Electronic Gong is an audible indication for lift arrival at a floor, which also has output to control lantern arrows. This low profile serial unit offers the choice of a single or double tone and is designed to be connected to the Dewhurst 4 wire serial encoders (CH024/034 or CX-Basic). The CJ70 is suitable for use with the Dewhurst Profile station, which could also include the 30mm and 50mm ULSP digital display unit.
- Serial gong (used without displays)
- Outputs to control lantern arrows
- Single or double tone
- Low profile
- Can be used to meet M2/S2 Building Regulations
- Adjustable volume
- Works with CH024/CH034 Serial Encoder or CX-Basic Encoder Board
Pit Ladders
Static stepladder with spacers for vertical attachment to wall. This design is intended to be used in elevator shafts with a reasonable amount of space.
- quick and cost-efficient solution
- the spacers can be positioned on the shaft wall in pairs relatively freely
- short installation time
Lift HAWK Sensor
The Lift HAWK is a sensor fitted on the top of the lift car (TOC) which can remotely check the lift status through connection with a Digital Communication Platform (DCP) or Memcom+. Information such as the time of the last lift movement, current door status and time of the last door move can all be remotely tested using this device. The HAWK also self-learns the typical activity of a lift and can autonomously perform lift tests in periods of prolonged inactivity.
- Remotely test the lift status without having to connect to the lift controller
- Self-learning sensor performs autonomous tests when usage patterns are not typical
- Real-time monitoring through the Avire Hub
- Saves time and cost of visiting site for false call outs
- CAN or serial connections
- Compact mechanical footprint
- Quick and easy to install
Shaft Lighting
Shaft lighting system with different protection classes for new systems or retrofits. Tailored solutions that are quick and cost-effective to install:
· Mark out the first light/wall mounting plate
· Drill
· Dowel into place
· Insert cable
· Move on to next light
· …all done
Keypads
The flush fitting MA Keypads combine robust vandal resistance with an attractive design to meet the most demanding of today’s concepts and specifications, in a wide range of applications from public services to specialist use in heavy duty environments and adverse weather conditions.
- Vandal resistant
- Wide operable key surface
- Wide range of legends
- Sealed to IP66
